rubble Posted June 4, 2016 Report Share Posted June 4, 2016 I'd like to have a cover made for my center console. Have used a grill cover for both the CC and the Leaning Seat but would like to get covers just for them. Any suggestions where to get them? Are there any stock products made for them or do all need to be custom? Link to comment Share on other sites More sharing options...
FINCHASER Posted June 5, 2016 Report Share Posted June 5, 2016 Custom is only option, be sure to see pics of their work first mine look like a tailored suit seen some on a friends boat that are way less accurate and tailored in the fitting. Not only does it look crappy but if it fits correctly once zipped up it stay in place on its own and doesn't flap around in the wind a lot. Not sure where you are at but I used Hetzog canvas in Ft Pierce. There is an initial cost ($100-150) for a shop to do a pattern. The shop gave me mine so I have it if you need it let me know and I can ,mail it to you to use. They would have to slightly adjust where the grab rail goes over the console cause I cut my grab rail off about 3-4" below the windhshield. Link to comment Share on other sites More sharing options...
rubble Posted June 5, 2016 Author Report Share Posted June 5, 2016 Could you snap a pic or two of yours? Is it a 2000v? Link to comment Share on other sites More sharing options...
FINCHASER Posted June 5, 2016 Report Share Posted June 5, 2016 Yeah Ill do it tomorrow and yes 2000V Link to comment Share on other sites More sharing options...
fin-addict Posted June 5, 2016 Report Share Posted June 5, 2016 yes there are stock products but the fit like garbage from what I have seen. have always had custom covers made. any canvas shop could do it. as suggested, look at their photo book first. prices range greatly. Link to comment Share on other sites More sharing options...
FINCHASER Posted June 5, 2016 Report Share Posted June 5, 2016 Link to comment Share on other sites More sharing options...
Bamaskeet Posted June 5, 2016 Report Share Posted June 5, 2016 While not form fitting, Coveralls makes an inexpensive console cover. Link to comment Share on other sites More sharing options...
FINCHASER Posted June 5, 2016 Report Share Posted June 5, 2016 I tried them when they first came out... lasted about 6 months and began rotting Link to comment Share on other sites More sharing options...
rubble Posted June 6, 2016 Author Report Share Posted June 6, 2016 Fin, do you think your console is the same dimensions as mine? I have a 2006 model. Link to comment Share on other sites More sharing options...
fin-addict Posted June 8, 2016 Report Share Posted June 8, 2016 not sure. my console has the built in cooler/baitwell seat in the front and does not have the built in side rod holders. my leaning post seat cover was approx. 250. other one blew off, forgot to stow it. full console cover closer to 350. if not mistaken. THINK THIS QUESTION WAS DIRECTED TO FINCHASER NOT FIN-ADDICT Link to comment Share on other sites More sharing options...
FINCHASER Posted June 9, 2016 Report Share Posted June 9, 2016 On 6/6/2016 at 10:09 AM, rubble said: Fin, do you think your console is the same dimensions as mine? I have a 2006 model. Im pretty certain the console in the 20' was identical in design and dimension throughout all years they were made Link to comment Share on other sites More sharing options...
rubble Posted June 9, 2016 Author Report Share Posted June 9, 2016 1 minute ago, FINCHASER said: Im pretty certain the console in the 20' was identical in design and dimension throughout all years they were made My CC has no built in cooler and it does have rod racks on each side. Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.